(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. M

    step up sherman trans will not fit in 9n

    whent to put a sherman in and the bottom gear on the trans in the tractor is straight cut and the two shermans that i have has helical cut gears , where can i find the proper shaft for the sherman to fit that straight cut gear
  2. M

    4000 row crop diesel exhaust

    what size and lenght is the vertical exhaust pipe supposed to be
    • mrhud
    • Thread
    • Replies: 5
    • Forum: Ford
  3. M

    881 with no serial number

    i have a 881 i am go ing to use for parts has diesel engine block cast number310609 the selecto speed trans has no numbers at all where the numbers should be the trans is blue under the red the cast on it is c3nn . question is this trans a new ford factory replacment why it does not have...
    • mrhud
    • Thread
    • Replies: 4
    • Forum: Ford
  4. M

    any one have a kramer?

    any one have a kramer tractor wondering how many are left
  5. M

    oliver 70 engine

    how big can that engine be made into , or whats the biggest that will fit in
  6. M

    oliver 70 engine

    what can be done to the 201 6cyl that is in the oliver 70, ? how big can it get ? or what will fit in ? thats pretty lite tractor with a 6 originaly
  7. M

    part onfront of 4000 row crop

    what is this part on the front of this 4000 and what is the seat and what about cushions
    • mrhud
    • Thread
    • Replies: 12
    • Forum: Ford
  8. M

    john deere b crankshafts

    i have a b82051 that has a crank that is realy bad would have to be welded i have a b 212731 that is going to scrap unless i can use the rods and crank in the hand start early b any know the differances. thanks Hudco
  9. M

    will a early ford narrow front 4000 fit on a 6000

    willthe front ends interchange could i take the narrow front end of a early 4000 the hundred series looking sheetmetal an d put that front end axle on a 6000
    • mrhud
    • Thread
    • Replies: 12
    • Forum: Ford
  10. M

    d17 6cyl gas or wd45 6 cyl gas

    does any of the antquie tractor puller clubs allow the d17 262 diesel or the wd45 230 desiel repowered with the 262 gas or 230 gas withou just being in a exibition class
  11. M

    any one use these small gps speedometers

    any one use the small gps speedmeters made for bicyles or cars looks like you can get about any of them for about 50.00
  12. M

    new 8n sheet metal on 9n

    how has poeple been attaching the new after market 8n dog legs on the bottom to 9n front axle support
  13. M

    new holland 1032 vs. 1036 balewagon

    how big is the differances? what are the differances?
  14. M

    37 wc weight brackets

    where is the best place to start out with weight brackets on this tractor
  15. M

    DuAl 125 looking for lift cylinder or barrel

    looking for part numbers for the barral ron and piston for a du al 125 loader i have one here that had the barrel dented in so i would like to find a used barrel or complete cylinder that i can rebiuld or at least part numbers to start looking for parts on the internet not inertrested in...
  16. M

    8n 9n dog leg parts

    is their a part that has the four bolts on the bottom of the dog legs to change over to the 8n with the one bolt, with out changing or fing a new front engine support would nice not to have fab parts
  17. M

    tuning carb, ignition , timing

    what you guys use besides a timing light ? , o2 sensor or vaccumm gauge or both ?
  18. M

    fastenal

    are all the fastenal stores gone ?
  19. M

    getting time for next years calanders

    where can i find just farmall , case , oliver, ford , mm johndeere , massey ferguson massey harris calanderers i allready get my allis ones
  20. M

    saginaw hitches

    are saginaw hitches still being biult
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top