(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. M

    20f dual clutch mess

    Just installed a new clutch and flywheel.When assembled The pressure plate levers are below flat like when the clutch is depressed.The pedal turned out really high and very stiff. The pto disc wouldn't disengage so I adjusted the stop bolts from .090 to .010 and got it to work but it's not...
  2. M

    massey 20F flywheel thickness

    on the same subject, the 20f has several clutch discs available. The metallic one is called out by MF but all the rivets sheared and tore up everything. Would a regular organic be better? It"s a lot cheaper.
  3. M

    massey 20F flywheel thickness

    I have a flywheel that needs approx .100 machined off to make it flat. The book says .040 max. I"d be willing to fab a shim between the wheel and crank if it would otherwise work. About 400 for a new one. thanks Mike
  4. M

    4000 HD ind backhoe hydraulic help

    yeah,sorry it must be a 1964. The last of the 4 cyl engines. I verified the plumbing yesterday and tried to seal up my loader control valve. It has some serious leakage from two round plugs on the bottom. I thought it was the hose fittings but I resealed them and it still leaks. I'm sure the...
  5. M

    4000 HD ind backhoe hydraulic help

    my loader control has a port marked out feeding the hoe.I assume power beyond.It also has a non adjustable relief stamped 2000psi.I'm guessing its worn and tired.My pump is new and sized for the machine. The 4500 looks like a lot more advanced machine than my 4000. I'm going to the hyd shop...
  6. M

    4000 HD ind backhoe hydraulic help

    Thanks John. I'm going to try taking the loader releif valve apart and see if I can shim it. Most all of my machinery would be scrapped by now if it wasn't for these forums and people willing to share their knowledge. Thanks a lot.
  7. M

    4000 HD ind backhoe hydraulic help

    I"ve got a 1965 4000TLB in poor condition. I put a new hyd pump on and changed all the filters and fluid. I checked the pressure at the backhoe valve manifold and it only has 1700psi. The relief valve was screwed all the way in and the spring is smashed flat. I added some shim washers and ran...
  8. M

    8n hard starting ballast resistor

    I did all the suggested stuff, points plugs condenser, still starts hard. I found when I jumper the factory ballast resistor the spark is noticably hotter. It measures about 1 ohm and the coil seems to get 5.5 volts when cold. I've seen detailed explanations of how the resistor helps starting...
  9. M

    3414 hydraulic service

    I bought a 3414 industrial loader and the only manuals I could find are just about useless. I got a new filter and I want to drain and refill the hyd system. It says hygard fluid and shows a plugt back on the 3pt lift to release trapped air. What about all the drain plugs on the belly? Thanks, Mike
  10. M

    identify industrial IH?

    I think it's a 3414. Bought it yesterday. I'm impressed with it. British built gas engine with carb problems but real solid machine. thanks for the replies. Mike
  11. M

    identify industrial IH?

    4 cylinder gas with 4 speed 2 range and shuttle shift. Any ideas on what it is? Thanks
  12. M

    3550 stuck in gear

    thanks Bill
  13. M

    3550 stuck in gear

    I'm looking at a 3550 stuck in 4th/8th gear. Hi and low shifts and the regular shifter moves but it won't change gears. It's a pretty solid state maintained machine with a nice factory loader and over 5000hrs. Any ideas on the value? Thanks. Mike
  14. M

    8n won't start

    48 8N 6 volt is a flakey starter. I've done all the ignition tuneup items and rebuilt the carb twice.It gets a lot of fuel in the lower intake tube but everytime I pull a sparkplug they are dry. The spark is not very impressive but i'd expect to see a wet plug. For some reason it likes short...
  15. M

    ID ford industrial

    It does have wet brakes. I'm pretty sure its a 3550. Is the stuck trans in 4th a possible disaster? Hi/Low still shifts.
  16. M

    ID ford industrial

    Can anybody identify this? They claim 1974 355D. I can't find any specs. Is it an oddball? Trans is stuck in 4th. Thanks Mike
  17. M

    4000 hd steering filter

    I couldn't get any auto parts store to cross reference a steering filter so I used the ebay link and bought the AE33538A equivalent filter. Not surprising it doesn't work on pump. I assume the HD is an oddball. I guess i'll take the 28.00 raping by my NH dealer and get something that fits.
  18. M

    4000 hd steering filter

    Scary stories guys...here's a testament to how tough the Ford is. I read a post on here about bleeding the fuel system after a filter change or other repairs. Somebody said they run the engine on ether until it bleeds itself.Nobody busted the concept so pumped nearly half a can in my tractor...
  19. M

    4000 hd steering filter

    Anybody have a p/n for the power steering filter on a 64 4000 hd ind 4 cylinder.I'm trying to avoid my local NH dealer. Also, is it bad to give her a small shot of ether when it's cold out. My intake heater plugs are shot and it lights right up with a little start fluid.Starts easy when it's...
  20. M

    4000HD digs but doesn't steer

    I'm using the same fluid as the hyd system. M2C41. It's mostly new because it blew a couple of hoses but it's cloudy so i'll try flushing it.The filter is clogged ruined so i'll change it to.What is a heavier fluid to try? Another question...When running the hoe the tractor likes to be almost...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top