(800) 853-2651
SHOP NOW

Search results

  1. Pete in MD

    Model B Pushrod Tubes

    On Sunday 46 chief asked how the tappets were oiled. The conversation eventually led to replies about pushrod tubes. The parts catalogs, PC-330 and PC-676, show that unstyled tractors and '39 & '40 models used 4 tubes, AB1284R. '41 models through the end of production used 2 tubes, AB2739R...
  2. Pete in MD

    Compression

    Anyone know what the compression was on a TC-MM engine when it was new? The engine is a model HEB, 605 cubic inch, 6 cylinder, stationary engine, built in 1946.
  3. Pete in MD

    Re: John Deere starter rod adjustment ( A, B, G, H, 40, 50,

    You're overthinking this. What I said is correct. There's lots of thread on the bottom end of the rod and the yoke needs to be screwed on far enough to avoid hitting the flywheel cover while at the same time having enough threads exposed to engage the starter switch. In other words it's a...
  4. Pete in MD

    Re: John Deere B Brakes

    You don't need to remove the snap ring to remove the first reduction cover. Remove the nut under the small cover. While pulling out on the clutch lever hit the end of the shaft with a lead hammer to drive it out of the bearing which will stay in the first reduction cover. Get some help as the...
  5. Pete in MD

    History of the Model Y, 62, and L tractors

    Some interesting reading from an email sent by Richard Hain, editor of Green Magazine. Green Magazine article
  6. Pete in MD

    Where was Barney ?

  7. Pete in MD

    A late funny

  8. Pete in MD

    Re: Thanks to John Deere Forum on 24 Volts

    You are correct on both systems.
  9. Pete in MD

    Hey dwwhite

    4 days ago you were looking for help with the Powr-trol on your '52 model G. Did you see my reply and was it any help to you?
  10. Pete in MD

    hey ZigZag

    Did you get the block removed from your '49 B ? Just curious as I replied to your post looking for help. Pete
  11. Pete in MD

    Moline 605 gas engine

    Can someone tell me what the cooling system capacity is on a 605 gas engine.
  12. Pete in MD

    605 Cooling System

    I'm going to do some work on an HEB (605 cu. in.) power unit. Can someone tell me how many gallons the cooling system holds?
  13. Pete in MD

    John T and other sparkies

    I want to put a solar battery maintainer on the 12V, 800 CCA marine battery in my dump trailer which doesn't get a whole lot of use. Looking on Amazon I see maintainers rated at 2.4, 5, 10, and 20 watts. What wattage would you recommend?
  14. Pete in MD

    6.0 Powerstroke Fuel Filters

    I changed both filters in my' 04 F-250 several years ago using a Motorcraft FD-4616 set of filters. Got another FD-4616 set last week from Amazon and the upper filter was way too small. The frame rail filter was the right size. Has the FD-4616 set been changed or did I get a mismatched set? Is...
  15. Pete in MD

    Feeling cooped up?

    Then take a little trip with Charlie Daniels. poke here
  16. Pete in MD

    Something to smile about

    . poke here
  17. Pete in MD

    Tx Jim - John Deere Factory Codes

    Is this what you were looking for Jim? A = John Deere Plow Works, Moline, IL B = John Deere Planter Works, Moline, IL C = John Deere Spreader Works, East Moline, IL D = John Deere Wagon Works, Moline, IL E = John Deere Ottumwa Works, Ottumwa, IA F = Syracuse Chilled Plow Company, Syracuse, NY H...
  18. Pete in MD

    Update---Removing Tire Rim as one unit

    Got 'er done today. Thanks to Mike M. and Ron for your help. First one took about 20 to 30 minutes, second one took less than 5 minutes. You're right Mike about hard to explain but easy to show how. I'm 80 years old and learned something new today, never too old to learn. Got the "new" wider...
  19. Pete in MD

    Removing Tire Rim as one unit

    My '48 B has cast centers with the lug nuts and wedges on the inside. I want to take off the tire/rim as one unit. There's a way to do this but I'm not sure what that way is. I suspect the position of the long notch on the outer edge of the cast center comes into play. Anyone have some advice...
  20. Pete in MD

    Hey, greenredneck

    Do you still want a copy of SB-268 ?
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top