(800) 853-2651
SHOP NOW

Recent content by 4fun

Yesterday's Tractor Forums
  1. 4

    Question for Mike Aylward

    Thanks guys I did see that but I was not sure if that was it or not. I was looking for a tube type like the #1&2. I will go with it instead of the kopper kote stuff like another friend uses, guess it worked for him.
  2. 4

    Question for Mike Aylward

    I would like to know where you find the #3 permetex at, I have a NAPA here and they didn"t have any and said that even the book that they can order from did not have it. Is it in a can or the sqeezeable tube? I will admit put it together dry and yes it leaked inside and outside, another costly...
  3. 4

    Toave's auction Dain Replica and Froelich

    The dain brought 3300 with no engine and the froelich brought 1400 and the engine was in bad shape
  4. 4

    Louis Toavs Auction 60

    The 60 O brought 7250.00
  5. 4

    First reduction gears on A

    Wondering if any one may know the number of teeth on a late A for the first reduction gear and the one on the pulley. Looking for a set to put in my two stick early A.
  6. 4

    Rear cover on an A

    Wanting to take off the power-trol off of my unstyled A and put on a flat back. I got one off newer A but found that the shaft is bigger and a different setup than the unstyled. Is there any way to make the shafts work with what I have or find the correct parts. thanks
  7. 4

    Rivet tool

    Where can I find a good quality rivet tool for installing new brake pads, or if there is something for an arbor press. Kind of sad but I called and left a message with a few different places and no calls were returned so thought I would do them for myself and some friends, thanks for any info
  8. 4

    Governor weights

    My weight pins and holes are a little woren and was wondering if someone makes oversized pins or what to make some out of that would be hard enough material so that they wouldn't wear out quickly. Also I'm guessing that is part of the reason why some will rev up and down and never carry a smooth...
  9. 4

    Torque specs for JD A

    Thanks for the info, I know I seen it on here before but didn't print it off at the time because I wasn't even close to that far along in the project yet.
  10. 4

    Torque specs for JD A

    I am looking for a link, or somewhere I could print off the torque specs for mains, rods, and head bolts or studs. Also curious what grade of fasteners did they use back in 1937.
  11. 4

    jetting on duplex carbs

    needing a little info on jetting, duplex carbs have two jets in bottom of carb by the bowl nut, i am wondering if a guy can put to big or to small of jets in there for a big change in elevation, i think the load screw is set and adjusts the fuel regardless of jet sizes, thanks for any help
  12. 4

    DLTX 109

    Thanks for the info
  13. 4

    DLTX 109

    I have a duplex dltx 109 and cannot find what it came off of. The tag also has 70EU stamped on it. The little round tag has dltx stamped in bigger letters on the top, 109 on the bottom in smaller numbers, and 70E on the left in bigger, deeper stamps also a U on the right. The plugs on the...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top