-
Ppomester replied to the thread head light wire placement TO -30.Here is the original technical drawing of the lighting system of the TO-30 - The stock system had the wire for the front lights run...
-
Ppomester replied to the thread Need help identifying tractor.A 620 would not have had a hydraulic pump or plumbing, correct? But would have had the pressure and return tubes running thru the...
-
PThe outside cleaned up nice, maybe too nice for "used red" 😜. The motor ain't pretty. Several gallons of water in the oil pan. But by...
-
Ppomester replied to the thread Thoughts on if the old girl is worth fixing? 1950 ford 8N.75 tips https://forums.yesterdaystractors.com/pages/artint268/
-
Ppomester replied to the thread Band sawmill."I want a shop/outdoor kitchen area and don’t want to pay the metal building price." - "I want something in the 4-8 grand range."...
-
PThe mesh can get so bad that no amount of solvent or rinsing will clean it properly. The spot weldsxare easy to drill out , remove the...
-
P18 MPH advertised at 2200 RPM and standard 12 X28 tires, so at 2400 RPM a little faster.
-
Ppomester replied to the thread Band sawmill.I hit a ceramic fence insulator one time. There was no powering thru that. No visible sign on the trunk that there was anything there...
-
-
Ppomester replied to the thread Band sawmill.Ya - people want me to cut power poles, I hate it, nasty stuff. If I can't get out of it, I charge a premium. Not to mention the...
-
PDad had bought one of the original Clarke mills. At the time they were building them in the garage next to their house. It was mostly...
-
PFor what it's worth, I buy and sell cut raw cut lumber. Do some cutting on a Baker resaw to make specific pieces that are required by...
-
Ppomester replied to the thread Band sawmill.Well - I am the other way. I have owned/used a WM LT40 for many years. It's not a business, although I can stay busier than I want if...
-
PI've got a 20 acre woodlot with lots of dying oaks. In your price range the mill will be very labor intensive, no bells and whistles...
-
Ppomester replied to the thread I Messed Up - Ford 3000 Distributor - Need Advice.Here's a disassembled 3-cylinder distributor. The screws which hold the clips for the cap also secure the points plate. The screws have...
-
-
Ppomester reacted to 4140 or bust's post in the thread ford 4000 4cyllinder power stearing with
Like.
Dusting off this old thread as well. I just made my own in about 30 minutes and wanted to share the materials that I used. Started with...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy