-
T
Massey 135 multi power
Thanks I figured so just hoping for easy fix 😩- to30man
- Post #4
- Forum: Tractor & Farm Talk
-
T
Massey 135 multi power
I have a 135 with the multi power stuck in low the fluid is full and the lever is going up and down on the top of the transmission but will not come out of low and engine will not hold tractor back going down hill. The safety switch beside the plunger is disconnected would that have any effect...- to30man
- Thread
- Replies: 8
- Forum: Tractor & Farm Talk
-
T
254 hay rake/tedder
I have a new holland 254 rake/Tedder and two of the plastic rollers are broken I got two off line for that model and the hole is to small and that’s the only ones I can find for that model. Has anyone ran into that issue thanks- to30man
- Thread
- Replies: 2
- Forum: Tractor & Farm Talk
-
T
Lift fluid 40
What is a good fluid for the lift on a John Deere 40 and I was switching the arm on the left side and one tractor after removing the bolt and washer it came right off the shaft and the other one I can’t get it to move any advise would be appreciated thanks- to30man
- Thread
- Replies: 1
- Forum: John Deere
-
T
40 engine rebuild
Is there a rebuild kit that comes with all gaskets seals piston and all I need- to30man
- Thread
- Replies: 7
- Forum: John Deere
-
T
John Deere 40 pulley
Trying to remove pin through pulley and shaft. Have heated and still can’t get pin to move any. Should I drill it out?- to30man
- Thread
- Replies: 5
- Forum: John Deere
-
T
John Deere 40 parts
Where can I find the final drive bearings and seals, cup bearing and gaskets thanks- to30man
- Thread
- Replies: 3
- Forum: John Deere
-
T
Final drive John Deere 40
Does anyone know where I can get a diagram for the final drive on a John Deere 40. I have ordered a shop manual but was hoping I could find the diagram online before the manual came in towards the end of the week but not having any luck thanks in advance- to30man
- Thread
- Replies: 2
- Forum: Tractor & Farm Talk
-
T
John Deere 40 final drive
I have to replace the two pictured parts does anyone have a diagram of the way to remove the axle? Will it slide out the back and then go back in with final drive on the tractor thanks- to30man
- Thread
- Replies: 1
- Forum: John Deere
-
T
Ford 4600 fuel leak
I have a leak on my 4600 injector pump it is on the plate where the fuel line is attached. The plate has a short nipple on it and it is leaking there. It is one piece so I think it may have a crack in it. I replaced the brass washer on each side of the part where the fuel line is hooked up. Does...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy