(800) 853-2651
SHOP NOW

Recent content by Valiant Farmer

Yesterday's Tractor Forums
  1. V

    MF 400 questions

    Hi all, There is a fellow I have bought several tractors off. He never has any real history on them. Anyway he has a Massey Ferguson 400. It has a blade and a winch. I haven't asked yet if it is for sale (I'm sure it is though - everything else is!) or the the price. All I know is that the...
  2. V

    Help With Farmall Magneto Mounting

    Thank you all for your help. I have attached a pic of the number on the head - And another one of the mag. Thanks, -Samuel
  3. V

    Farmall A?

    Thank you all for your help. I have attached a pic of the number on the head. Also another one of the mag. Thanks, -Samuel
  4. V

    Help With Farmall Magneto Mounting

    I have been notified that the number I have pictured above is the casting number/part number. The serial number plate is missing on the tractor.
  5. V

    Help With Farmall Magneto Mounting

    Hi all, A couple questions- How is the top of the magneto meant to be mounted? And is this a Farmall A - Is the serial number the number by the gear stick I have pictured below? Thanks! Samuel
  6. V

    Farmall A?

    Hi all, I bought a Farmall tractor a few months back and am wondering if it is an A - I can't find the serial number under the seat, is it the number by the gear stick I have pictured? We have finally got it running! How is the top of the magneto meant to be mounted? Thanks for your time! Samuel
  7. V

    John Deere 3140 MFWD

    Yes will be replacing the rod as well! Thanks
  8. V

    John Deere 3140 MFWD

  9. V

    John Deere 3140 MFWD

    Hi all, I bought a John Deere 3140 MFWD, and I was told it had a bit of noise, maybe valve adjustment necessary. I have bought a lot of tractors from him, and he has been great to deal with. I went to check it out and it wouldn't run, or even turn over. It had been running a couple months...
  10. V

    684 Head Gasket

    I have a IH 684 with a D239 Turbo, whats the deal with aftermarket head gaskets verses the one I can buy at IH dealers? Any particular gasket makers preferable (available in NZ). How is the quality of Sparex gaskets vs someone like Bare-Co? Thanks Joshua
  11. V

    Zetor hydraulics

    I will, only why wont the PTO work unless the tractor is in gear? Where is the pump located? Thanks
  12. V

    Zetor hydraulics

    I have a Zetor 6711, and the PTO and hydraulics do not work (excepting only the ground speed PTO). I have tried the lever in all positions. Is it possible that there is a broken shaft or clutch plate? Both PTO and main clutch release pedal-to-lever links are missing, so the PTO "brake" lever is...
  13. V

    MF 40 Industrial

    Hi all, I have just bought a Massey Ferguson 40 tractor off a local market gardener. The history is as follows - Used for potato shifting, as it HAD a forklift (someone used a gas torch and cut the heavy gauge steel, and stole the forklift! The theft was not noticed till a long time after, and...
  14. V

    35X clutch

    Dual clutch. I replaced the throw out bearing as well. The old bearing had seized and had hastened the end of the screws. BTW is the rear main seal a rope seal like the Dexta? I have split and put it together again, so I could test the clutch, as I bought it without knowing clutch...
  15. V

    35X clutch

    Hi all, I got a Massey Ferguson 35X with a collapsed thrust bearing and clutch finger screws worn out. I've replaced them. I've adjusted the PTO plate lifting bolts so the tolerance and height is correct. The the plate and cover is very oily. With a 600mm adjustable wrench on the PTO...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top