Mudrig's new Ford 3000

[Sean in PA]

Just an FYI - That is not a 3000 grill. Both the early and later style 3000 grills were two pieces. That grill looks like the style from a later 2600/3600 series, but the background on those were originally black, so either it's very faded or someone repainted it incorrectly. That grill was not designed to be installed in that shell, so if you get the shell back to it's original shape, the grill won't fit. I would just bang the shell out until that grill fits inside and call it done.

 

[Mudrig150]

Just an FYI - That is not a 3000 grill. Both the early and later style 3000 grills were two pieces. That grill looks like the style from a later 2600/3600 series, but the background on those were originally black, so either it's very faded or someone repainted it incorrectly. That grill was not designed to be installed in that shell, so if you get the shell back to it's original shape, the grill won't fit. I would just bang the shell out until that grill fits inside and call it done.

It's a 3600 grille, and I bought it knowing it wouldn't be a direct fit, I just prefer this grille style.
It's silver because the mesh isn't painted, but I might just clear coat it and leave it silver because I think it looks neat.
The reason it won't fit right now is because the whole grille shell is bent to one side, so both sides are skewed enough to make the grille hit on the top corners, and it's also making contact where the top is all caved in, so neither style grille will fit until it's straightened out.
Brackets on the original style grille don't line up at all but they're broken anyway, at least, the lower grille tabs are.

 

[gears]

Great work Mud, there's just something satisfying (to me anyways) about making what you have work. I just spent an hour out in the barn fabricating 1/4 of an inner fender for my old Dakota (PO got hit and cut chunks out to get it on the trailer)....

 

[Mudrig150]

Drawbar obtained, had to fight it to get the drawbar into the bracket, and unfortunately the swing plate bracket is bent just enough that it doesn't swing freely... oh well, it moves with a hammer at least.
It was a nightmare to find since I haven't seen a single 2000 or 3000 with the drawbar for sale or parted out.

Hoping to pick up the year-a-round cab that'll go on the tractor this saturday.

 

[Mudrig150]

Just noticed something really worrying... while up under the tractor I noticed I could see light through the wheel center... turns out both centers are super thin around the bolt holes from rust, and the left side actually has some siezeable rust holes around the bolts... I only have 1 good rim, while having two leaking tires, two rusted wheel centers, and 1 rotten rim that has the loops breaking off.

 

[Destroked 450]

View attachment 165508

Drawbar obtained, had to fight it to get the drawbar into the bracket, and unfortunately the swing plate bracket is bent just enough that it doesn't swing freely... oh well, it moves with a hammer at least.
It was a nightmare to find since I haven't seen a single 2000 or 3000 with the drawbar for sale or parted out.

Hoping to pick up the year-a-round cab that'll go on the tractor this saturday.

Sounds like you put a 4000 draw bar on your 3000, they look the same but 4000 draw bar is slightly thicker

 

[Mudrig150]

It's a bit ragged, but it's perfect for modifying to fit the 3000. Roof isn't super rotten and it's got all the windows intact minus a door window that's broke and the cracked rear glass.

 

[Mudrig150]

And a slightly better picture in the daylight...
I don't plan on adding a heater back so I'll probably just try and squeeze an evap core where the heater previously was.

 

[Mudrig150]

Bit stuck... both in regards to progress and also just in regards to the pittman arms. They are STUCK. Had my biggest puller on them and even using my big impact I couldn't get them to budge. Someone has clearly been in here before so I'm a bit concerned with what I'm gonna find once it comes apart to reseal it...

 

[a49deere]

Had the same issue with my 3910 arms. Fired up the torch, already had the puller on arm, just got the torch on to arm, Bang!! Off it came, And I do mean off it came! Don't stand in front of it!!

 

[Mudrig150]

Had the same issue with my 3910 arms. Fired up the torch, already had the puller on arm, just got the torch on to arm, Bang!! Off it came, And I do mean off it came! Don't stand in front of it!!

I was actually able to pull them off with a smaller puller. Not sure why it worked better, but whatever.