(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. M

    Columbus Nebraska dealer for Don

    This tractor is at Eisenmann Supplies in Madison Nebraska, 801B, engine tight, never seen a tractor with a fuel pressure gauge. The dealer became an IH dealer and was called Red Country, my brother and I bought some tools from that auction 20 years ago. Don't know much else.
  2. M

    Dealer list

    I didn't get a good look at the sticker, but it said Case Equipment, Columbus Nebraska. On a 530? Will try and stop next week and get a pic.
  3. M

    JD B overdrive

    Friend called and said he found a b that might be going to scrap and wondered if the overdrive is worth keeping. Acreage is being leveled and this tractor was in the trees. NE Nebraska
  4. M

    454-1066 rear light plug/3 wire connector

    Does anybody have part numbers for the 3 wire connector and the rubber plug/grommet for the rear light on these tractors ?? thanks chris
  5. M

    666 rear crankshaft seal

    Funny problem, put a clutch in this tractor and replaced the seal. I went to rotate the engine and it is tight. Rolled it back apart and can only rotate the engine 1/2 a turn and stops. Planning on removing the seal and see if it rotates. I have the tool to install the seal, the original didn't...
  6. M

    Dash/hood cowling 666

    Has anyone bought the cowling from Reliable aftermarket parts on ebay and does it fit ??
  7. M

    666 rockshaft/three point oil level

    Had to replace the eccentric for the draft control, couldn't find a drain, so just sucked out with a siphon tool. Got my IT manual back last night to see there is a drain plug, but didn't have time to look at the tractor to see where it drains, and then no mention of refilling the housing to...
  8. M

    Deere 112 UPDATE

    It is a Tecumseh engine, removed the hood and front grill to get coil wire on, and seen the ID tag, Model SBH-172A, serial 2004. Got it running but sounds like the head gasket is blown under the shroud. Couldn't restart after it was running a few minutes, will try again when I haul it to my shop...
  9. M

    Deere 112

    Is there an easy way to move a dead machine ? Looked at one last night and it didn't seem to move to easy by hand. Good shape just need to get running for a friend and rather leave it where it's at than dragging it home. Never worked on one before, found I need a plug and wire for sure, are the...
  10. M

    586 case forklift 188 sleeves

    Brother called and is going to overhaul it, coolant in the oil, found old and new sleeves protrude 0.010 where it should be 0.001-0.003, anybody run into this before?? No shims. thanks
  11. M

    530 engine oil lines

    Can these be made easily, I am in the process of replacing crankshaft seals and noticed one broke off just above the fitting on the pump. Relative had sediment bowl/carb issues and filled the crankcase with gas. Must have run it a bit since the crankcase is spotless other than the hard sludge...
  12. M

    New aluminum distributors any good.

    Just curious if any has put some time on a tractor with the new distributors. I installed one for a guy but don't think he uses tractor much. One guy said he never could get his tractor to run right with one. Pins and weights are shot on mine(1942 H), I use this tractor for moving snow and...
  13. M

    Behlen live pump seal numbers ??

    Have a leak and going to replace the seals, have the back one out but cant quite make out the number, will stop by bearing store and find out what's available. thanks chris
  14. M

    68 4020 PCV cracking

    Had leak in dash area and found the pressure control valve cracked. This happened a few years ago and we just replaced with a used one. Anyone run into this problem ? Tractor is used to feed cattle with a 148 loader. Was Dads tractor so I know about it for the last 50 years. Think the hyd...
  15. M

    630 main bearings

    Where do you get main bearings for the crankshaft, machine shop is having issues finding the small end undersized. Deere might scare me a bit. thanks chris
  16. M

    Super h upper bolster bushing

    Does the bushing wear out or does the shaft wear out. Have one that has a lot of play in that area and before I dig into it or the customer doesn't want to go that far, I would like to know.
  17. M

    630 rod bearing

    Friend took his tractor out that hasn't ran much lately and the flywheel side bearing seized and killed the engine. So we took the cap off to find bad bearing, but at least nothing stuck to the crank, can't even feel anything with our finger nail. So thinking the rubber packing between the case...
  18. M

    Fast hitch cylinder seal kit

    Does anybody make up a seal kit for the 3 1/2 inch cylinders, one CIH dealer said no more and other said over $200. Have a hyd place that I might be visiting.
  19. M

    Milwaukee Sockets

    Has anyone used 1/2 deep impact sockets of this brand. Daughter thought I needed a Mil. 1/2 battery impact for Xmas, Now looking for sockets to go with the wrench. They have very complete sets in metric and standard. thanks chris
  20. M

    440 info

    Serial 8200535, looks like it is a triple range, shuttle, has a foot throttle, 3 pt., power steering, gas engine. 1963 model ? Can a pto be added easy?
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top