(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. B

    Oil pump cover update

    Finally got to the cover today, sanded fairly easily. Huge difference, i,dont have a great straight edge, im using a 6 inch Square, does the cover have too be 100% flat? I can see a little light but I can see an equal amount on tge housing when I check that...my guess is 2 gaskets...
  2. B

    Super a oil pump w/pics

    Hey fellas, i pulled the oil pump cause I didnt have good oil pressure, right on the line between red and white on the gauge. The gasket is certainly missing in spots and the gears have worn into the cover quite a bit on one side and slightly on the other...what do you suggest? It seams lije a...
  3. B

    Fan hub oil

    I removed the fan to work on the govenor easier and the oil drained out of the hub, how much should go back in and I assume it's just engine oil? 10w30 would work? Thanks
  4. B

    Radiator hose

    Anyone know where to get 12 inches of 2" I.D. radiator hose? All I can find is 3' lengths and I only need 6 inches for the tractor. All the pre cut pieces are 2.5" long and they barely have enough room for the clamps to seat properly in my opinion. Thanks, anthony
  5. B

    Fan belt size

    I have a super A with a non pressurized radiator and no water pump from a early A. The engine is a c123 but the fan belt measures 3/4 x 33.5 which is for a c113. There are various sizes within an inch of what I have now. Should I go with the standard A belt which is slightly smaller than what I...
  6. B

    Governor slop

    I I opened the "a" governor and the spring was intact, the thrust bearings looked fine, so I put it back together and noticed the clevis rod on carb side was rubbing so I flipped it so the bend ofthe rod was facing the carb and no more rub, throttle on carb opens and closes freely. But when i...
  7. B

    A govenor

    I have almost no throttle response, if I move the rod on the left side of the tractor to the rear I get plenty response, just vary little from the seat and only on the idle end. I had to take the radiator off to get boiled out and a leak checked out so it's all open. I was thinking I should...
  8. B

    Gear oil smell

    I cleaned the tractor with a heavy duty degreaser last year that really worked well but the rear end grease smell didn't really go away. I was thinking simple green or zep orange cleaner for the smell, any suggestions? Thanks Anthony
  9. B

    Rustyfarmall, Rustred, and the rest THANK YOU

    Thank you fellas for your patience and help with this carburetor, I finally have it running right and no leaks, I really do appreciate it guys !!!
  10. B

    Carb still leaking and won't run without choke HELP

    I soaked the zenith carb for my A for a solid week, I i cleaned everything out with carb cleaner spray. I installed a new needle jet, new needle, new gaskets. I adjusted the float to 1 5/32 but it just seems to low but I've been told that id's what it is. The float is good, new gaskets, I...
  11. B

    Float level

    This zenith carb in my Super A calls for 1 5/32 but it leaks at that setting. I talked to a guy yesterday and he laughed and said just set it level. This sound right or is the 1 5/32 a must? Thanks
  12. B

    Throttle and choke shaft questions

    I'm going to replace both these shafts in the carb and had a question about the packing... the kit includes both shafts, new screws, a felt washer, felt packing, plug and retainers. I've never replaced these before, the directions say neoprene seals but I have both felt and neoprene, and felt...
  13. B

    Rtv for manifold

    I have black and #2 etc and only go 400 and 500 degrees... should I go get copper rtv? I might have a slight leak in the manifold gasket that I wanted to seal up just in case. The last guy had whay looked line orange rtv plastered all over the manifold gasket, he may habe known something I...
  14. B

    Autolight 386 vs 3116

    There were autolight 386 plugs in the Super A when i got it. It has a mag so I put 3116 in because they're non resistor plugs and i guess that's what you need to use from what I've read but are these hot enough? I've read that if your plugs are not hot enough you'll have to use choke to run...
  15. B

    carb to manifold bolts

    can someone tell me what size the bolts are from the carb to manifold on a A / Super A....the bolts that are there now are replacements, not sure if it had a stud kit or bolts...thanks anthony
  16. B

    Rustred quick question

    The well jet and economizer jet won't come out, the screw heads are destroyed but the passage ways look fine so i wasn't going to new with them . I'm assuming they have gaskets so when I soak this carb later today it's probably going to eat those gaskets away. Think this is going to create a...
  17. B

    Rustred, carb question

    I'm going to pick up a gallon of gunk tonight. The main jet assembly was already put together so I assumed the guy before me reinstalled correctly, I know I know, so I'm guessing I should pull all of that apart before soaking? I don't have the jet install tool and cash is tight, do I need it ?
  18. B

    Rusted carb question

    I'm going to pick up a gallon of gunk tonight. The main jet assembly was already put together so I assumed the guy before me reinstalled correctly, I know I know, so I'm guessing I should pull all of that apart before soaking? I don't have the jet install tool and cash is tight, do I need it ?
  19. B

    At wits end with carb please help

    So I rebuilt the carb with the kit that came with the tractor when i bought it. It was boiled out at the machine shop then I sprayed it with carb cleaner and shot air through the passages 3 times. I re tightened the manifold bolts, tightened the crap out of the carb to manifold bolts. The...
  20. B

    Governor start-up question

    Super a started up earlier then died like it ran out of fuel. I pulled the carb went through it again, put it back on, and nothing. Turns over but won't fire. I checked the govenor rod and it was almost unresponsive with the throttle. I removed the gov to carb rod and the linkage from...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top