(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. W

    4320 Draw bar pin holder replacemenr

    Does anyone know how the updated draw bar pin holder works on a 4320? I have looked at the parts break down and I can’t figure it out. New pin is 18.
  2. W

    4320 hydraulics slow

    Used my 4320 yesterday the 3 point is very slow to react, and then will drop down on while turning for my return pass moldboard plowing.
  3. W

    Help 4320 and 630 tractors

    Need some help with my two Deere tractors: 630- lost the gas cap and bought 2 new ones from Deere. the cap continue to leak gas when the front is tossed around. I have replaced the cork gasket multiple times. Any idea on how to stop the gas from spilling out the top? 4320 one of the hydraulic...
  4. W

    John Disc model H1200 trailer disc

    I have an older John Deere disc the gang shaft broke, and I want to get a new one. Shaft is 1 1/8” width total length is 61” subtract the threads I am 59”ish. Can anyone help me locate a new shaft? This is the best I have found...
  5. W

    3pt disc disc for 630

    Would an 3pt 8ft series 200 dirt dog disc be too big to run behind a 630 John Deere?
  6. W

    Follow up 630 fly wheel leak

    I finally got around to switching out the Oring on the auto shut off carb today, and got to investigate the oil leaking out of the bottom of the fly wheel cover. There were no real visible oil leaks. The oil had pooled some by one of the cover bolts near the back side of the fly wheel cover in...
  7. W

    Rebuilt clutch

    Has anyone used an aftermarket rebuilt clutch for a 4020 or 4320? Deere no longer loans out the tools. I would have to purchase the tools Thanks
  8. W

    630 engine oil leaking under fly wheel cover

    I got on my 630 and noticed the engine oil pressure was very low. Got down and looked and found oil leaking out of the fly wheel cover. Any idea what would cause this?
  9. W

    630 top link rebuild

    My top link ball has what I would describe as chatter marks around the John Deere ball and then a sleeve. I purchased the parts needed to rebuild the locking mechanism. Is there anything I need to pay very close attention to?
  10. W

    630 1st reduction casting cracker

    I have spent a bunch of time working on the families 630. Last night I got to go look at the 630, my dad some how cracked the bottom portion of the first reduction casting behind the drain plug. My father was running a 6ft bush hog. I can not find any indication of the casting being hit from the...
  11. W

    630 John Deere top link

    I bought a used 3 point off another 630 John Deere. The arms are cat. 2. I can not get the locking mechanism to close around a cat. 2 ball. Did Deere make the top link cat.1 or is my mechanism messed up?
  12. W

    4320 John Deere Step washer?

    Slowly going through a new to me 4320, and am slowly replacing and fixing items the last owner did not do up to my standards. The tractor has a two steps to get to the platform. Can someone please confirm if the steps are original or an after market set up? If the steps are original can someone...
  13. W

    4320-1971 Front Tire size

    The tires on the tractor are 11x16s should I go with these or replace them with a different size? Going to use this tractor for tillage 5 bottom plow and disking. Thanks
  14. W

    F1450 5 bottom plow

    Having trouble locating a parts break down for 1450 5 bottom plow for my 4320 JD. Looking to replace all of the wear parts. The landsides and frogs are alll. Is this common?
  15. W

    Glencoe cultivator

    This afternoon some got a tree root and lost the the two pieces of steel the first piece that attaches to the spring portion then the next flat steel piece that holds the point. Anyone able to help me find these two parts?
  16. W

    4320 Lift Link

    Looking for a left handed lift link for a 4320. In a pinch would it be ok to use a 4020 lift link until I can source 4320 lift link?
  17. W

    Thank you 630- Lift yoke Seal

    Just wanted to say thank you to everyone on the form who provided insight on replacing the seal for the lift arm yoke on my 630. Took me two whole days to tear it apart and put it all together. Thanks
  18. W

    4320 Air Stack Lenght

    Wanted to know if there was a length recommended for the air in take stake on John Deere 4320? The muffler stack extension was removed so the tractor could be stored inside. Believe the stack will have to be cut to fit as well. I have notice some tractor without the air stack. What is the reason...
  19. W

    630 upper lift arm rebuild

    Going to be rebuilding the center link arm bracket on my 630. Believe there to only be a couple little plastic washers to replace. Has anyone done this before, and are there any items that I should be looking to replace while taking everything apart. Thanks
  20. W

    4320 Drawbar support- who would you go through

    Slowly working on my 4320 John Deere and getting ready for this spring. I noticed my draw bar support is bowed and worn. I checked with Deere part NO AR33911 sub is AR33911-1 and I can get the following OEM $561 Deere After market dealer AI for $450 schoups-$299 Yesterday days tractor $189
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top