(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. E

    SOS problems I could use some help

    I have a Ford 901 with the SOS trans . I was running under 3rd gear without a load and the tractor stopped moving forward. I have no speeds not even reverse and the PTO doesn"t spin now also. It makes a noise which sounds like a Buzzing noise or what might be called a whine. Any help greatly...
    • ENJ62
    • Thread
    • Replies: 8
    • Forum: Ford
  2. E

    Massey pacer

    Did the pacer have a oil filter for the hydraulics on the pump side of the engine forward of the steering box? ED
  3. E

    Pony N62 valves

    I was wondering if anyone has come across this. The exhaust valves on my pony .Dont have the tapered keepers , but rather pins like the intake. These are aftermarket I'm sure. There is a difference between the valves and the number on the exhaust indicate an exhaust valve So my rebuilder tells...
  4. E

    N62 Oil Pump question

    Has anyone purchased the rebuild kit from Montes for the N62 oil pump . I recieved 2 bushings . One looks to be made out of oilite bronze which is short in length 1/4 inch long. The other looks like copper and is split. I realize the oilite one is the bushing that goes in the housing but whats...
  5. E

    MH pony sicklebar manual needed

    Would anyone have a copy of the manual for the Pony sicklebar. I was given one but its all disassembled . I need to reassemble it and figure out how it mounts to the tractor . I have a feeling its missing a few things. Thanks ED
  6. E

    Front tractor tire dilema

    I am restoring a 1954 MH Pony that was used by a town for highway mowing with a sickle bar. I have purchased new R3 diamond patterned rears from Goodyear What would a highway dept normally use as a setup for the front with the R3 rears ? (a tri rib or 5 rib)This tractor will be for occasional...
  7. E

    Adjustable front axle question

    I have a tractor I just aquired with an adjustable front . The inner axle tubes are rusted tight. What I noticed is one axle when looking at what would be the king pin is straight and the other is at about 5 degree angle caster.this was due to one side missing its locking pin . Is this going...
  8. E

    Gray Pony color info

    This has been a difficult task of figuring out what the true color of the gray Pony should be, but I think I"ve figured it out after speaking to the editor of Ferguson Furrows. The light gray which is the NAPA 3740 wasn"t being used until Dec of 1954 ,so that would mean the correct color would...
  9. E

    Pony clutch assembly question

    I ran into a problem that is delaying the reassembly of our Pony. When we removed the yoke that causes the throwout bearing to disengage the clutch we failed to notice how it was mounted. This yoke piece is held on by 2 bolts and contacts the casting the throwout bearing is mounted to. We are...
  10. E

    Can Epoxy primer and Vari prime question.

    I have a tractor I am restoring some parts are bare some were coated with variprime by my sandblaster so they wouldn't rust. I want to shoot the tractor with an epoxy primer after assembly and then a Polurethane topcoat. Can epoxy primer go over Vari Prime? Thanks ED
  11. E

    Pony tie rod dust boots / covers

    Does anyone know where to buy tie rod dust covers for an adjustable axle Pony. I'm not having much luck finding these, yet I have seen tractors at shows in the past with brand new ones. Specifically need a number or what to ask for . If you say NAPA the guys at mine are very lazy when it comes...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top