(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. D

    Metal cutting cold cut circular saw

    Get a Slugger Metal Cutting Saw and their blades . Depending on blade used they cut aluminum , stainless , carbon steel up to 5/16? thick. Used by lots of metal fab shops . They are a hot saw . Blade speed similar to wood saw.
  2. D

    9n lift arms

    Bought a set of Pats Easy Lift 3point lift attachments. His parts are sized for lift arms between 2 and 3 inches high. Mine are 1 3/4 which affects the mounting. Only one set of the 4 bolts that squeeze the lift arm hits the lift arm. The wedges with the roll pin hole are not thick enough to...
  3. D

    9n radius rod removal

    I am in the process of removing front end stuff prior to doing a front axle pin removal. I want to remove the radius arms at the front axle attachment point. The nut came off easily, but I can?t get the bolt to move. It seems to be really rusted in.i have tried PB blaster and tried moving the...
  4. D

    posting pictures

    How do I post a digital picture I have taken to this forum
  5. D

    9n starter 6volt

    thanks for the rapid input from you guys ! I took that info and some info from past posts on this site,and the starter is back working.I verified that the battery was OK and checked all terminals.Solenoid checked out OK also.Based on some old posts I decided to check if the starter had shorted...
  6. D

    9n starter 6volt

    My starter seems to have gone out.Just a little bumping sound when starter button pushed.When I jump across solenoid terminals i get same sound. Any tricks for replacing it. I have read that you don"t want to spin the starter before its mounted or the starter gear moves out on the bendix and...
  7. D

    8n no spark

    I think I mislead you guys.When I said the wire to the Distrib was hot i meant there was current to the coil terminal.I did not mean there was a hot [temp] wire.
  8. D

    8n no spark

    My neighbor has a front mount 8n.His motor quit running after it had been running Ok previous day. After checking things out he discovered no spark at plugs.His wire going to distrib. is hot. Any ideas where he should look?
  9. D

    9n ignition switch help

    Which site sells the most reliable ignition switch.I have read on this site that most are junk,and I agree completely.I"m getting about 6 months use B4 they start acting up.They aren"t failing due to weather or abuse,they just quit !!!
  10. D

    48n 6v front distributor no spark

    I just went thru a bad ignition switch.New switch that was only a couple of months old.Tractor started running rough.Would only keep running with choke pulled out.Replaced the " new " switch,tractor runs fine.
  11. D

    9n ignition switches

    Any opinions about the source of the best quality ignition switches?I've read comments on the Forum re poor quality ignition switches that are out there.I just had to replace a switch that was maybe 2 months old.Not sure what tractor parts site I got it from.
  12. D

    Problems with a 9N

    I totally agree with Dell.Prove your ignition switch is OK.I just dealt with a 9n that was running erractically.Sometimes it would run fine,sometimes it would stumble a little,sometimes it would only run if I kept the choke on.Everyone said the same thing.Prove you have fuel flow by removing the...
  13. D

    9n carb problems

    Are you saying you would choose the Zenith over the Marvel as sold on this site? Per my post I did a flow test out the drain plug and it was fine.Haven't checked spark yet.
  14. D

    9n carb problems

    I have a 9n with an 8n front mount 6v motor.Motor running perfectly yesterday for a couple of hours bush hogging.Its always started and run fine.Started it this morning and it only wants to keep running if choke pulled out.4 gals. fuel added yesterday at end of day.Thats the only change from...
  15. D

    9n on cover of new N-news mag.

    Nice pic. of a 9n on the cover of the new Spring issue of N-news.One thing I noticed right away was the flexible fuel line that appears to be sitting on the exhaust manifold.Big fire read to happen??
  16. D

    Mounting the gas tank

    I think the parts manual and shop manuals show the tank bolted to hood cross framing using 3 bolts.there are soft pads between the tank and framing bolt points.
  17. D

    OT So Crazy, Better, Worse, Thanks for you guys being here!!

    my sympathy to you and your family.Its amazing to view all the support that showed up on this forum.Its like a big extended family that is lending support.
  18. D

    9n hood side panels

    I have the hood side panels with the dimpled holes at the bottom for attaching to the front axle support.Its just the side panel with a hole in it and the axle support with a hole in it.I have a service manual that shows a Part# 8434 that is part of the attachment down there?Do I just bolt...
  19. D

    Help Replacing Crankshaft Pulley???

    I recently removed my crank pulley bolt by putting trans in neutral.My pto shaft has about a 1/4" hole thru it.I put about a 2" long bolt thru the hole.An adjustable wrench or a big pipe wrench can then be used without having to grab and maybe damage the PTO spline.The handle of the wrench was...
  20. D

    9n foot rests

    Does anyone have any pictures of what the stock 9n foot rests look like? This site sells foot rests that they say are for 9n,2n.My existing rests are some sort of homemade diamond plate that is welded to the peg coming off the rear attachment for the radius arms.The rear support for the foot...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top