(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. M

    TO 20 Transmission cover

    I was going to replace my transmission shifter cover gasket on my TO 20. I was wondering are there any surprises that I need to watch out for while trying to remove cover? Thanks for any info.
  2. M

    Replacing Starter Switch TO 20

    I am going to replace my starter switch on my TO 20 and was wondering if all that you do is remove the 2 bolts on top and lift out? Never done it before and didn't what any surprises. Thanks for any information.
  3. M

    12 V Headlight bulbs

    I was wondering where I could purchase new 12V sealed beam headlight bulbs that will fit a TO20. I looked on this site and all that I have seen are 6V. Thanks for any information.
  4. M

    Cleaning Hydraulic Pump

    I was planning on dropping my hydraulic pump to clean pump and replace my lift cylinder this spring on my newly acquired TO 20. I have read that these are exactly the same as a 9N. My question is are they the same as far as removing the pump and lift cover? Thanks for any information.
  5. M

    Whats the right oil filter for a TO 20?

    I am a little confused about the correct oil filter for a TO 20. The archives suggust a NAPA 1107 but they dont make this filter anymore. The NAPA 1010 is for 9N8N2N and I have read somewhere that this isn't correct for a TO 20. Baldwin makes a P40 and thats what this site sells but it cross...
  6. M

    Idling Oil Pressure

    I am in the process of having my TO 20 rebuilt at a repetable tractor repair shop. The mechanic told my that he replaced all bearings, plastigauged all journals and rebuilt the oil pump. However he seems to be having trouble getting the oil pressure to get any higher than 5 to 10 psi while hot...
  7. M

    Compression test question

    I recently did a dry compression test on my newly acquired TO 20 because it doesn't run quite rite and it has 1 oil fouled plug. The readings where 100 to 105 on 3 cylinders. The reading on the oil fouled plug cylinder was 60 to 65. I added a little oil to the cylinder and the reading jumped to...
  8. M

    Motor Knock

    I recently inherited a 50 TO 20 in reasonably good condition. Before I got it the tractor has not run in 6 or 7 years. I replaced all wiring, points and rebuilt carb. Changed all oils. The tractor starts easy and runs well and smokes very little. However the motor knocks at low RPMs. Whenever...
  9. M

    PTO Question

    I am new to the Ferguson site. I recently inherited a TO20 in pretty good shape. I have 2 8N's and I am very familiar with them. My question is will a PTO shaft out of a 1950 8N fit a TO20? I have one that has a good collar on it so it should not leak. Just trying to save a little money. They...
  10. M

    Transmission Trouble

    I recenty rebuilt the motor and replaced some other parts on my 8N refurbish project. The tractor runs and drives fine now. The tractor hasn't ran for 25 to 30 years before the rebuild. The transmission will shift into 2,4 and reverse but not 1 or 3. During the engine rebuild I took the top...
  11. M

    8N Rebuild Oil Pump Question

    I am rebuilding a 8N 1950 engine. After 3 oil pump orders (manufacturing crap) I finally received one that I could press the gear on with. My question is that now 1 or 2 of the oil pump gear teeth are slightly longer than the others and I have a bad drag will rotating the pump. Is this...
  12. M

    Front Axle half spindle bushing question.

    I recently purchased a junked out tractor to restore. On disassembly of the front axle I noticed that the spindle bushings just dropped out of the axle housing. I tried to install a new bushing in the axle half and it will barely touch the sides of the housing. My question is can you JB weld the...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top