(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. J

    Ford 1910 oil dipstick question

    I don't know if I lost it somehow or someone decided they needed it but either way it's gone. And dumb as it is I can't remember if there was a tube or just a stick. If anyone has a picture that would be great or could tell me what I need. Thanks. ..dumb I know lol...
  2. J

    1910 fuel in oil

    I have a 1910 and it's getting diesel in the oil. I'm not sure from where? Don't know if it's an injector or maybe a seal at the injection pump. Any help is appreciated.
  3. J

    4230 hydraulics not working

    I have brakes and steering. I don't have 3 point and remotes. 3 point control was seemingly kinda stuck. 3 point was raised in up position and I could not lower it . I took linkage off at 3 point shaft coming from tractor. Am able to move it now as it freed up and 3 point lowered but will not...
  4. J

    4230 wiring harness source

    Does anyone know where I can find a wiring harness for a 4230? I've tried here. eBay...local place with no luck. Do they exist or does everyone just make them thereselves.
  5. J

    Difference in brands of injectors

    Goes on jd 4230... checking eBay I see prices from about 23 to 65. I was wondering if anyone had bad or good things to say about the cheaper ones. Or if they had a preference with any.
  6. J

    4230 fuel in oil. Leaking inj. Pump ?

    Oil level rising. Not water. I've replaced lift pump. Guess it's coming in thru inj.pump. Never had one off on tractor before. Tractor starts and runs good. Is this something I can fix or do I need to take to injection pump shop?
  7. J

    ford 1910 differential lock problems

    Both wheels are locked in. Bought it like this. I took the hydraulic line loose next to it so i can see inside. The lever will not stay in the up or down positiion...springs back to center. Works smoothly. Not sure how its suppose to be but thought it suppose to stay in one position or another...
  8. J

    ford 1910 differential lock wont disengage

    I just bought a 1910 and i dont have a manual yet. The differential will not disengage...meaning both wheels are being powered etc It makes it very difficult to turn. Ive tried going slow and hitting brakes as well as jacking it up and rocking right side rear tire. Guess ill have to tear it...
  9. J

    differential problem/question

    I do not know the correct name of the part in question...it is on the bottom side of the differential. It is a bracket with the bolt that holds the lower part of the 3 point in place/pivot. There just seems to be one small bolt holding it to the diff. housing. That bolt broke, the bracket...
  10. J

    hydraulic problem----hydraulic remote????

    i have a case 1175--i used a disc the other day. It raised and lowered like it should although toward the end i was thinking it was getting slow and also i didnt fold the "wings" of the disc up/down etc...just raised it and lowered it as a whole. Today i go to use it, folded it up, raised it up...
  11. J

    case 1175 pto issue

    I have a new pto pump. I can run a shredder for 75 yds and it will work fine and then the pto pump makes alot of noise ( not eneough to really hear inside open cab/no windows) but very easily heard when you get of the tractor. Pressure is showing 160 regardless of noise. After the 75yds the...
  12. J

    how much hydraulic fluid in a case 1175

    I know there are site glasses on the side but i just realized there were also some type of change up to the amount of hydraulic fluid that was needed and some case tractors you had to add more than the site glass showed...and they used a dipstick in the back.-------------does anyone know the...
  13. J

    case pto question

    Long story short--case 1175 1. should the pto pressure rise with acceleration? 2. Do you you remove or add washers/shims etc to increase pressure?
  14. J

    case 1175 pto clutch

    hey guys, hopefully someone can help me out......ive got a case 1175 and i am attempting to replace the pto clutch. I have that section out or the factory manual and ...? nothing really looks like it does in the book, although it very well could be me not reading it right. To be clear, in...
  15. J

    case 1175 weak PTO

    Trying to shred...the pto does not keep turning correctly in thick weeds. As i understand it my problem will be one of these.. 1. hydraulic pump/pressure---assume this is good since batwings raise as does the shredder. Not slow, seems to work normally. 2.control valve 3.cable that works the...
  16. J

    how do you know when you have the throttle cable on right

    What i mean is throttle wise....I replaced a throttle cable on my 1175 and at first i could not power up past 1000 rpms...i readjusted the position of the cable and then took it up a little past 2000 rpms with a little more travel that i didnt use.---Before i get into a field pulling something...
  17. J

    case 1175 hydraulic fluid/ filter etc

    i have a case 1175 that i have been slowly refurbishing. I have a manual coming in the mail but i need to use it asap.I need to add hydraulic fluid. The only plugs i have seen was on the left side. 1 plug says add the other says good. Dunno why they didnt just use 1 plug but whatever. 1. I am...
  18. J

    hydraulic leak gasket question

    I have a leak and i am not sure what i need to order. I dont know correct terminology...but the leak is occurring right where the 3 point hitch arms pivot at.Right where they connect to the tractor at. I wasnt sure if it is just a gasket there or some type of rubber bushing or something.
  19. J

    where to find case throttle cable

    I have a case 1175. The throttle cable broke. I checked with the local case tractor place and after some searching they said they could get one for $75. I checked this site but there is no listing for one. Just gonna ask if anyone has a better place to get one?
  20. J

    front end loader strength

    was wondering how much weight can your typical front end loader thats on a 8n/9n can lift...also weight that the front end can handle?---specifically does anyone use them to move round bales of hay?
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top