(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. K

    New Holland 451 sickle mower

    This message is a reply to an archived post by Traditional Farmer on May 30, 2018 at 05:25:20. The original subject was Re: New Holland sickle mower. I know this is an old thread but I ran across it while working on a NH 451 that was given to me. I am in need of the drive plates that...
  2. K

    6' finish mower behind 8n

    I hooked up a 6' land pride finish mower to my 52 8n. If I go up any incline big or small it bogs the tractor down no matter which gear I am in. then when attempting to get back on flat surface my radiator starts steaming out of my radiator cap. Is it just to much for my tractor or Is my...
  3. K

    Idle Issues on 8n

    Several weeks ago I was having an issue with loss of power. 8n would idle great but bog down when attempting to let clutch out to move and if trying to move up any small incline would lose power and die. I took carb off and made sure it was clean. I had rebuilt it a couple month ago...
  4. K

    transmission Issues

    I have not drove my 8n for a month or so. However, I have started it periodically. Yesterday I started it up and let it run for 5 to 10 minutes. I have it parked in a shed that has a slight hump to get over in order to back it out of shed. Each time I would attempt to let out the clutch...
  5. K

    Painting an 8n

    When the weather warms up some I want to start painting my new to me 8n. I have read though some of the archives on different approaches. I am doing this on a limited budget and was planning on brushing the red and rolling the hood/fenders. I have read where people rolled the hood and...
  6. K

    Changing Oil in 8n

    I starting changing oil for the first time in my 8n. When I removed the drain plug I noticed there was no screen connected to it. I waited until the oil finished draining and then noticed the screen appeared to be inside the pick up tube. I could move it around but could not pull it out...
  7. K

    No Spark on 8n

    Hey guys I have a problem I can’t seem to resolve. A couple of weeks ago I rebuilt my carb and had tractor running great. Did not start it for a couple of weeks. Went out yesterday to clear some snow off and could not get it to start. I thought I just flooded it because I had gas...
  8. K

    Re-wiring a 8n

    I have a question regarding rewiring an 8n. I have looked at JMOR's wiring pictograms but can't find what I am needing. I have a 52 8n with side mount distributor. It has been converted to 12volt and has a 3 wire alternator. All of the pics show the late 8n's with 1 wire alternators. The...
  9. K

    8n Hydraulic rebuild (gaskets)

    Hey guys, I purchased a lift cover gasket set off this site to use as I rebuild my hydraulics on my 8n tractor. These appear to be just paper gaskets. has anyone had any issues with them? or is there a better material/quality product to purchase somewhere else?
  10. K

    Draining the hydraulic tank

    Just a question. Pulled the last two drain plugs. The small 9/16 plug at very rear of tank and the next one right infront if it. There are two more. One under the gear shifters and then the front one under the motor. My question is, do I pull all three plugs or just the last two?
  11. K

    Universal Drawbar Lock

    Do you guys think one of these would be sufficient. Or do I need one on the left and right side of drawbar? I will only be pulling a small 5x8 trailer.
  12. K

    8N hydraulic Piston Rebuild

    hey guys, I have begun a hydraulic piston rebuild and have a question. I soaked the leather o-ring in hot water for about 5 min. It was actually pretty easy to get installed compared to some of the horror stories I had read about. However, the leather ring seems larger and sticks out past...
  13. K

    Thoughts on SHELL SPIRAX S4 TXM

    Has anybody used, SHELL SPIRAX S4 TXM for your 8n hydraulics? if so what were your thoughts on it?? Thanks
  14. K

    1952 8n 3 point lift question

    Good morning I am new to the site and new to tractors. I just purchased a 1952 ford 8n and am having fun learning how to operator it. I have read a lot on these tractors as far as the PTO is concerned and have a question. I was using a boom pole the other day to remove a blade from a...
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top