(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. D

    35 B jumping out of low range

    Our 35 B likes to jump out of low range for no reason, any idea what to look for. Thanks in advance
  2. D

    JD 70 carb

    Question I have is about a John Deere 70 carb, Doesn't seem to be getting enough gas to # 2 cylinder, tractor will idle fine on #1 But no matter what, I can't get it to idle on #2, soaked carb 2 times, but read that need to take balls out to clean passages, is my only option to send it out, no...
  3. D

    Roberts carburetor

    Does anyone know if roberts carburetor is still in business, haven't been able to reach anyone on the phone for over a week.
  4. D

    J 70 carb

    I'm sure it's been gone over before but what is the best way to get those little balls out so I can clean the passage ways so I can get it to idle properly
  5. D

    john deere a brakes

    I have 2 John Deere A's, 1 styled, 1 unstyled and when driving it makes a growling sound until you push on the brake pedal just a little then it goes away when you let off it may come back in a minute or two, any idea what I should look for
  6. D

    john deere b pistons

    Looking for .045 over pistons for a 1937 B, can only seem to find ones for later models, any ideas where to look, would prefer new, aluminum is fine.
  7. D

    Tractor day

    Had a small tractor day this weekend at my place, 22 tractors in all, farmall,jd, and 1 minny, one good time.
  8. D

    M wiring diagram

    Looking for a diagram for a farmall m, 12 volt generator, positive ground, with magneto, and a 3 position switch, must have something hooked up wrong cannot get it to change, have had generator checked out twice and it is working. Any help would be great. Thanks Doug
  9. D

    IH Gauges

    Need gauges for my farmall m, just wondering where to get good gauges, no junk.
  10. D

    8n pto

    I have a 8n that sems to be stuck in gear when you let the clutch out, but when you spin the pto shaft sometimes it frees up and then you can let the clutch out and the tractor seems fine. seems like something is sticking in the pto.
  11. D

    power steering oil

    Wondering what is the best oil to put in a JD 70 power steering, I read somewhere 10w would work. Thanks for the info.
  12. D

    JD 70 wiring

    Looking for a good wiring diagram for a John Deere 70 gas with a 12 volt positive ground.
  13. D

    JD 70

    I am restoring a 70 and was looking for a few parts and was wondering a good place to get gauges, upper water pipe, and a thermostat, the thermostat seems to be a little different and John Deere wants $190. Also the speed and hour meter. A little worried not all parts are created equal. I will...
  14. D

    JD 70 Clutch

    I am rebuilding the clutch and pulley on my 70 and now have it back together and trying to adjust the clutch but no matter what I do when I push the lever forward it will not snap in gear it just pushes forward to a dead stop. Could I have something wrong with the clutch dogs or something else...
  15. D

    JD70 steering

    On my 70 where the steering shaft goes into the valve actuating sleeve both are wore out bad and I was wondering if there was a fix or do I need to replace the parts and if so where can I get the parts. It does have power steering. Thanks for your help.
  16. D

    Ford 8n

    A friend of mine has a 8n and the other day was driving it seemed to lock up and kill the engine, it will run fine with clutch pushed in but when you let it out it bogs the egine down and stalls it, doesn't seem to be locked in gear. Any help would be great. Thanks Doug
  17. D

    Gasket

    I have a large gasket I am putting on a JD 70 that the gasket seems to have shrunk over time, is there any way to stretch it back to size without tearing it or would it be easier to make a new one. Thanks Doug
  18. D

    John Deere 70 clutch gear

    I am having problems putting the drive gear on the back of the clutch pulley, I have heated it up with torch and it will only go on about half way, it was very hard to get off also. Are they just that difficult or am I missing something. Thanks for your help. Doug
  19. D

    John Deere 70 clutch

    I am putting on new spring clips that hold the clutch cover on, and was wondering how you go about peening the rivet over so it holds the clip. Thanks for the help
  20. D

    Massey 135 throttle

    We have a Massey 135 gas that the throttle linkage is all wore out under the dash, and throttle handle itself is bad also, Massey dealer says no parts available, any suggestions?
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top