(800) 853-2651
SHOP NOW

Recent content by a4

Yesterday's Tractor Forums
  1. A

    lookin for tires

    i have a set of Firestone Long Bar Short bar 23 deg with 3/4-7/8 bar in Pa. 570-430-2586
  2. A

    lookin for tires

    i have a set of Firestone Long Bar Short bar 23 deg with 3/4-7/8 bar in Pa. 570-430-2586
  3. A

    VFD for phase conversion?

    located in Pa., do you lose efficiancy of the motor with these?
  4. A

    VFD for phase conversion?

    I have been reading some posts about VFD's for 3 ph to single conversion.Could someone please tell me what and where to look for? I have 3 phase Rockwell mill with a 3/4 hp motor
  5. A

    Building a Flowbench

    Has anyone ever built a flowbench from any of the many designs and satisfied with the results? wi50's head project is what I would like to try on my 6 cyl Deere.
  6. A

    Shop Air Line

    I do alot of work at P&G plant,safety up the wazoo.They use copper with solder joints,stays clean never any problems.You have to be certified to solder there.
  7. A

    2 3/8 carb

    Prob looking for a aircraft carb Stromberg NR 7 or the larger NR9 Ask on Pull Off.com they are on ther frome time to time
  8. A

    injectors

    M yset up is from a Diesel truck,G pullers set up is very similar.
  9. A

    injectors

    I have done about what you are going to do but I have not fired it up yet.I got a late 720 [same as 730,830]set of pumps.I sent them to 2 cyl diesel shop along with my 70 injectors. He updated them to a 730 style tip along with other mods.He rebuilt the pumps and made them capable of supplying...
  10. A

    Rockwell milling machine

    I have a small rockwel vertical milling machine.I see collets listed a s R-8 .Is this the same as Bridgeport R-8? I have a Br R-8 tool that seems to long and will not go up in the spindle. al
  11. A

    9, 9-1/4Connecting rods?

    for a 6 cyl deere project on gas
  12. A

    9, 9-1/4Connecting rods?

    Anyone know of connecting rods with a 3 inch big end by 9 or 9-1/4 long?
  13. A

    JD 820/830 Governor

    I think you are doing the right thing getting the govenor to stay "with" the engine .Roger Marlin says that is key to the 2 cyl diesels performing the best.
  14. A

    Tire Weight Difference

    185 lbs for the 18-4's n a bath scale
  15. A

    wrist pin bushing

    B-544 [leaded phosphur bronze] ,532,534,545 are similar. I read this is what KB engines used............ What bore are your pistons? comp height?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top