(800) 853-2651
SHOP NOW

Recent content by Steve (NC)

Yesterday's Tractor Forums
  1. S

    Piston Hydraulic Pump Bearing Ring

    I am trying to rebuild my hydralic pump on a 53 Jubilee. It has the round piston pump style. I am down to the last part which is the bearing sleeve. I have tried the approach of using the oil seal to bang it out, now I have nothing left of it to use. I need some help. Any ideas or advice. My...
  2. S

    Rebuilding hydraulic pump

    Thanks Dean. That worked. Any tips for getting out the pump shaft seal? The hydraulic rebuild DVD mentioned a race puller. Thanks again, Steve
  3. S

    Rebuilding hydraulic pump

    '53 Ford Jubilee I need some help. I am trying to rebuild the hydraulic pump (piston style) and can not get the plate out of the pump cover/head. I think the old gasket underneath it has 'glued' it in. Any advice? I appreciate anyone's help. Thanks, Steve in NC
  4. S

    Need trick to installing thermostat

    53 Jubilee... Trying to install new thermostat on tractor. After cracking one thermostat housing and a leak with the new one, I was wondering if there was a trick to installing it back on. I am guessing that the thermostat is sliding out of the groove some when I try to place it back on and...
  5. S

    Radiator cap

    I ended up getting my radiator repaired on my Jubilee. Shop said the overflow tube or pressure release tube was clogged up. He put a new tube and neck on it but I think he kept the cap. What pressure radiator cap should I pick up at the auto parts store? 7, 13, 15, 16? Thanks for any responses...
  6. S

    Hole in Radiator

    Is there anything I shoud look for in the water pump or thermostat? Should I get a pump repair kit just to be safe? When the radiator was geisering the temp gauge was pegged at 250 degrees. Thanks for the replies. The repair shop is looking like a good solution so far. Thanks, Steve
  7. S

    Hole in Radiator

    I have a 53 Jubilee with a hole in the seam at the top of the radiator. At first it was just a tiny stream and tractor worked fine. Yesterday it turned into a geiser of steam and tractor began sputtering. Thought it was going to die out. I am not sure what to do. Should I just order a new...
  8. S

    Need help removing axel bearings

    Got it off. Thanks for the reply. Just took a little muscle and a hamer with a cold chisel. New axel installed. -Steve
  9. S

    Need help removing axel bearings

    I am trying to install a new rear axel into a Jubilee. Any advice on removing the bearing sleeve without damaging it? Is it possible? Thanks, Steve in NC
  10. S

    Different Axel Nuts

    Hello All, I got a flat in one of my rear tires and had to take wheel off. Decided I was going to replace brakes while it was off. Bought some parts including axel nuts (ordered 4179). When I went to take the axel nut noticed it was a larger inner diameter than the one I ordered on one side the...
  11. S

    Rebuilt hydraulics, new issue

    I am a beginner with tractors. If the vane pump is a square shape, then I have the piston style pump. -Steve
  12. S

    Rebuilt hydraulics, new issue

    Thanks for the response. Can you explain what you mean by costly? Is there more to fixing it than the pump repair kit? Thanks, Steve in NC
  13. S

    Rebuilt hydraulics, new issue

    I rebuilt the hydraulics on my 53 Jubilee. Took awhile to prime the pump but I finally got that going. I love the fact that the arms now stay up. But now when I try to lift the arms they stutter slowly going up. Does not matter if they are loaded or not. Goes down nice and fast. Any...
  14. S

    Hydraulics rebuild

    I agree with Bruce. It is probably the O-ring around the piston. I just finished rebuilding the hydraulics on my Jubilee. Same problem. Discovered the O-ring around the piston was all broken up. I found the DVD on hydraulics rebuild to be helpful. Also a little note, it took awhile for my...
  15. S

    Different Wheels

    I have a 53 Jubilee with two different rear wheels. One is the 6 spoke and the other is all smooth. Which one is the correct wheel? Thanks, Steve in NC
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top