(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. A

    9600 electrical schematics

    Worked on a 9600 today that I know little about. Starts and runs by applying power direct to starter. Does not turn over with key. Wiring is a mess down by the starter. Not sure where the yellow wire goes or what the small little electrical box is circled in red. Anyone have knowledge of this...
    • Abbby
    • Thread
    • Replies: 1
    • Forum: Ford
  2. A

    Ford 3000 hydraulic pump

    I have a 1965 Ford 3000. Is the plug circled below the bleed plug? If I loosen this while running should oil squirt out?
    • Abbby
    • Thread
    • Replies: 5
    • Forum: Ford
  3. A

    Ford 3000 hydraulic top cover adjustment

    How far should this nut be threaded down the shaft? I have the full service manual and do not see anything about this.
    • Abbby
    • Thread
    • Replies: 3
    • Forum: Ford
  4. A

    GE4440 bulb

    My Ford 3000 has GE4440 bulbs and one is burnt out. Seems to be a hard bulb to find. Is there a new number out there I can use that has the three prong plug? I would be ok with std or LED.
    • Abbby
    • Thread
    • Replies: 2
    • Forum: Ford
  5. A

    1965 3000 hydraulic override adjustment

    So trying to follow the manual about adjusting the hydraulic override. States to measure from cover surface to cam follower on control arm then add .010 and that's what the adjuster should sit above the deck surface. Do I measure the adjuster the way it sits or push down on it? is does push in...
    • Abbby
    • Thread
    • Replies: 0
    • Forum: Ford
  6. A

    Ford 3000 hydraulic valve seat

    Does anyone know? When driving this valve seat back into the top cover is there a required orientation to this hole?
    • Abbby
    • Thread
    • Replies: 3
    • Forum: Ford
  7. A

    wheel weights

    Does anyone have a picture of the special segmented wheel weight that goes where the valve stem is?
  8. A

    1965 Ford 3000 hood support rod

    Can anyone show me a picture of how the hood rod is stored away when the hood is closed? Mine has no place to secure and it wants to fall onto the battery,
    • Abbby
    • Thread
    • Replies: 9
    • Forum: Ford
  9. A

    1965 Ford 3000 hydraulic section question

    In the process of replacing the hydraulic oil pickup tube. Quite a challenge to get it out plus will be fun putting it back. My tractor came from overseas and has the hand brake. I have removed that and will not put back. Underneath the special gears for the hand brake is a sheet metal part...
    • Abbby
    • Thread
    • Replies: 1
    • Forum: Ford
  10. A

    Ford 3000 front axle pin stuck

    Any new ideas on getting front axle pin out besides a torch? I tried heat and 4 foot pipe on breaker bar. No go. Has anyone had luck with large impact wrench? I tried Sawzall blade and the ones I have do not even put a nick in the spacer. Hard stuff.
    • Abbby
    • Thread
    • Replies: 14
    • Forum: Ford
  11. A

    Ford 3000 hydraulic question

    I acquired a 1965 Ford 3000. Previous owner had hydraulic apart and tractor has not ran in a couple years. 1) Can I run engine without hydraulic oil in the sump? 2) Once I get all back together and try to start it should I prime the hydraulic system or will it prime on its own without harm?
    • Abbby
    • Thread
    • Replies: 1
    • Forum: Ford
  12. A

    1965 Ford 3000 hydraulics

    Just picked up this tractor where previous owner had taken top lift cover off for some issue. Attached is what I have. Does anyone have an exploded view of this part of the tractor? Is there an online parts available for free? Figure I will put in new orings and gaskets and see what happens.
    • Abbby
    • Thread
    • Replies: 8
    • Forum: Ford
  13. A

    Ford 9N oil lines

    I am looking to make new oil lines going in and out of the oil filter, Thinking of using copper. Anyone know the size and are these a simple single flare which can be done with this tool?
  14. A

    tractor for sale

    Not mine https://minneapolis.craigslist.org/csw/grd/d/swanville-ford-tractor-with-attachments/7621532681.html
  15. A

    Work light wiring

    Can someone share good methods to route/secure the wire in the back for the work light? Mine is shown in the pics but does get caught once in a while because it is not protected.
  16. A

    Oil filter conversion

    Can someone who has installed this oil filter conversion. Can you explain to me what is involved with oil lines? Can original oil lines be used or must they be replaced? Seems replacing can be tricky especially for the front one.
  17. A

    Fuel shut-off valve replacement

    Ford 9N - When replacing fuel shut off valve is there a recommended sealer to be used on the threads where the valve screws into the tank? I have read Teflon tape. Is all Teflon tape gas resistant?
  18. A

    spin on oil filter adaptor lines

    Can someone explain the process for installing one of these oil filter adaptors on a 9N? My main concern is the oil lines. Will both need to be replaced and if so what line did you purchase to make it work? How about routing the front line. seems I remember that being very tight fit. Thanks in...
  19. A

    9N governor setting

    Can someone confirm this. It is my understanding that the fixture and setting gauge are not required to ensure the .220-.230" spacing is correct. Check with a caliper and if too large add some shims and if to small take some out? Not sure implications of too large or small. Seems if gap is too...
  20. A

    camgear replace as a set? 9N

    When replacing camshaft gear does it need to be replaced as as set with the crank gear? I am think not seeing the crank gear is steel and cam gear is aluminum.
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top