(800) 853-2651
SHOP NOW

Search results

Yesterday's Tractor Forums
  1. R

    2630 with 145 loader

    My 2 lever control valves on a JD 145 loader are going bad (sticking), I'm thinking of going with a joy stick replacement. Any recommendations of where to begin my search?
  2. R

    2630 TACH

    Hi all, I am replacing my JD 2630 (1974) tach, I put a cheapo import in a few years ago....a mistake. It didn't fit correctly 1st off, and failed after only 200 hours...any recommendations? Deere apparently quit making them, I see aftermarket replacements starting at $35.00 up to $200.00...
  3. R

    starter button

    Hello all, I have a JD model 50 (1956) , not get engaging the starter, I did all the usual, clean the battery posts, went underneath and cleaned all connections inside the button and post on the outside. Checked for juice, got a good result, but still no engagement. The inside of the button...
  4. R

    1650 front end

    Hello All, I'm posting a pic of my 1968 gas 1650 project my son and I picked up in baskets a year ago. Upgrades included 15.5 new rear tires, (came with 12.4 which was on the build card and were very dry rotted) hi flotation on the front, cheap aftermarket seat which actually is fairly comfy...
  5. R

    Hay Rake

    suggestions on used hayrakes, I am currently using a well wornJD 640, looking to up grade. Small operation of grass hay (30acres), Looking at 256 NH, with or without dollies, possible Miller Pro. I'm not sure about the wheel rakes, plenty around that are cheap. My budget is about 2500.00...
  6. R

    Hay Rake

    suggestions on used hayrakes, I am currently using a well wornJD 640, looking to up grade. Small operation (30acres), Looking at 256 NH, with or without dollies, possible Miller Pro. I'm not sure about the wheel rakes, plenty around that are cheap. My budget is about 2500.00 thanks in advance.
  7. R

    1650 3 point hitch

    My 1650 lower lift arms are missing the locking mechanism that holds the pins on the arms in place.I can see where the pins will begin to walk out with much use. Where can I get the proper parts to replace? It looks like a small 1/4 bolt with an over size washer was there before. thanks for...
  8. R

    1650 Governor

    '68 Oliver 1650 Gas job. When I start it, sometimes it will throttle all the way up and then drop down to idle. Is this a governor issue, and how can it be corrected? thanks in advance for any/all comments!
  9. R

    1650 rear rim/tire

    1968 1650 gasser, creeper gear option I mentioned this before awhile back, this 1650 I have was set up for vegetables apparently, with the wierd tire / rim configuration. 12.4 38 rears mounted on a 13 rim. It was noted most rims are even numbered, but here is the tape measuring bead to bead...
  10. R

    1650 power steering leak

    1968 1650, gasser. Restoration project. Just noticed oil coming from the base of the steering wheel. I looked behind the dash, nothing wet there. Suggestions how to address this issue? Also, when you start the engine, it revs high then calms down to an idle, works fine afterwards. Governor...
  11. R

    OLIVER 1650 ELECTRONIC IGNITION

    The distributor on my '67 1650 has been replaced with the rtp distributor #1112587-TD, is there an electronic ignition that will work in this setup? Most say they fit the orginal Holly ditributor. thanks in advance.. Bruce
  12. R

    Farmhand wheel rake

    I have an old Farmhand 4 wheel 3ph rake. I've never used one, is it worth fixing up to put in service vs a side delivery rake?
  13. R

    1650 tires

    I recently purchased a 1650 gas that came with 12.4 rear tires mounted on a 13 rim. The're very dry rotted, so I want to replace them. will 15.5 fit on a 13 rim, or should I just go with 13.6? In addition this tractor came with a creeper trans, as opposed to the hydra shift. I'm thinking...
  14. R

    Bush Hog Flail Mower

    Hello, I just obtained a Bush Hog Flail mower model FH174. Pros and cons? I know its no longer manufactured, but parts seem to be available on the web. Some of the knives are missing, I'm not sure if they're rough cut, or fine though, more research to do. Thanks for any advice!
  15. R

    Oliver 1650 steering adjust

    The steering adjustment just below the power steering motor is stuck, any suggestions on freeing it up?
  16. R

    CIH Disc Mower 82MD

    Hello all, I have been using the 3pt hitch disc mower CIH MD82 with great results for about 5 years now! My question is, is it normal to not be able to level the 3 pt hitch with this machine? The load bearing (right) side must be lower than the left to attach to the tractor, and its a pain to...
  17. R

    2630 Hydraulics

    Howdy all and happy Memorial Day! I have a '74 2630 with independent PTO, dual remotes, small pump. Hydraulics will not work unless pto lever between the shifters is engaged. The master pto control doesn't have any effect. Pto works when engaged with the master and independent lever also...
  18. R

    OLIVER 1650 SEAT REPLACEMENT

    Any suggestions for complete seat replacement? I'm sure I can make a "universal" fit. The structure of the original is pretty poor.
  19. R

    Oliver 1650

    I picked up a project 1968 Oliver 1650 gas model that is in good shape. Stored inside. So far, we've put a distributor, cap rotor, wires, and plugs on it. Still cleaning the fuel tank, it starts, runs excellent! Now in the process of getting all the old hydraulic fluid out, without a drain...
  20. R

    2630 hydraulics

    I'm looking for info to install belly remote outlets on my 2630 for my loader. I've plumbed from the back for years, but I want to put it mid belly to get rid of the long hoses and free up that remote. thanks in advance for help!
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top